ATF EMMC Pin Finder v11.90 Update!! 30 JAN 2015

 

Release Date: January 30, 2015
Firmware Version Required : 11.0.10
ATF Box USB Driver Required: 2.10.0.0 - Windows 7/8/8.1 (32-bit and 64-bit)
ATF Box USB Driver Required: 2.8.30.0 - Windows XP (32-bit and 64-bit)


[New ATF Box Firmware]

LogiCore 11.0.10
* Added FIRST-IN-THE-WORLD eMMC Test Point Finder/Locator Engine
* Improved eMMC Read/Write Speeds
* Added more VCCIO Level Adjustments options

[ATF Plus]

* Added Find eMMC TP - eMMC Test Point Finder 1.0
* Absolutely FIRST-IN-THE-WORLD Feature which allows you to Locate the eMMC
Programming Test Points WITH-OUT Removing the eMMC Chip from the PCB.
* Supports Qualcomm, Marvell PXA and Broadcom CPU for CMD and CLK Detection
* Supports Exynos for CLK Test Point Detection
* Other CPUs will be supported soon


ATF eMMC Test Point Finder Tutorial

Reserved [ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذا الرابط] : How to make tp cable

Very Simple TP Cable Schematics
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]


Sample of Home Made Cable
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

Please Take Note of the Following Items before Attempting to Find CLK and CMD:

1. Make sure you connect Positive (+) and Negative (-) Terminals Properly and Correctly.
2. Make sure POWER BUTTON is ALWAYS PRESSED
3. DO NOT Connect USB Cable to Phone
3. Allow at least 2 Tries per possible Location on the PCB
4. DO NOT Exert Too Much Force on the Resistors as they may COME OFF!!!
5. For Exynos Based Phones, you can only Find CLK using this method. CMD Can be found using another Method.
6. Not all Phones have exposed CLK or CMD Locations on the PCB.
7. Not all Phones are supported with this NEW TP FINDER Method. ATF Team will continue to improve it via UPDATES.


STEP 1: Connect Power Positive (+) and Negative (-) to the Phone's Battery Terminal
STEP 2: Make Sure Power Button is Always Pressed. Use Rubber Band or Tie Cables.
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]


STEP 3: Setup ATF Software settings such as REPEAT and INTERVAL for your convenience
REPEAT <--- Number of Times TP Finder will Loop Itself Automatically
INTERVAL <--- Delay in Seconds before the next TP Finder Operation will Start
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]


STEP 4: Start Connecting Test Point PIN to Resistors/TP Pads on the Phone's PCB around the eMMC Area.
Wait for Message "Please Check Another Location..." before trying other TP Locations
On ATF BIG Chrome Box, change TP Location when GREEN LED will Power OFF
On ATF Nitro/Lightning Box, change TP Location when BLUE LED will Power OFF
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

In this Example, I tried all the Locations that were marked with RED
DO NOT TRY TO TP a CAPACITOR, it is NEVER CORRECT
Capacitors are BROWN in COLOR
Resistors are BLACK in COLOR
ONLY TRY TO TP Resistors and Test Point Pads around eMMC Area
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]


When a correct Test Point is Found, you will see similar Message Below.
The message also shows you the PINOUT of ATF RJ-45 Socket for the proper connection of the Test Point Found.
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]



If Test Point is not Found Around the eMMC Area, you can try looking for it around the CPU Area.

[GENERAL UPDATES]

--> Added all variants of Microsoft Lumia 330 in Nokia.ini



*******************************
ATF JTAG 1.0.13 Build 5935
*******************************

Release Date: January 30, 2015
Firmware Version Required : LogiCore 11.0.10

Change Log
--> Uses new ATF Firmware LogiCore 11.0.10
--> Adjusted eMMC Read/Write Timeouts

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذا الرابط]