Samsung s3 i9300 & Note2 N7100 & i9500 s4 Dead boot
repair solution & imei null solution only for i9300
Procedure:
* Download samsung s3 boot card maker Download
* Extract it on desktop
* Take a card reader insert memory card into the card reader nd connect it to the pc
* From the extracted folder run Diskdump2.exe
* Select generic storage Device. pictures below follw it
* Now to write the scripts folle the below given picr
Now done yu are succesfully created Dead boot memorycard
To continue further
Requerments:
* Z3X samsung Box or SPT Box (i used z3x)
* special UART Cable (300k or 500k uartcable)
* Download teraterm-4.78 From Download
* Fully charged battery
Dead boot Reapairing procedure
* Download nd extract teraterm-4.78 on desktop
* From extracted folder run ttermpro.exe there select serial port nd change the serial port to z3x serial
port lik below givin in the picr
*After Select The Serial Port Press Ok Button den Go To Setup Click Serial Port Option
Select Baud Rate 115200 Then Press Ok Button lik below givn in the picr
* Now insert the created boot card to the mobile
* Connect the Uart cable via z3x box
* Now Insert the battery nd wait for 5min if the procces didnt start discnnt the mobile close ttermpro agin try it.
* if it run success yu vil the result below given lik this.
repair solution & imei null solution only for i9300
Procedure:
* Download samsung s3 boot card maker Download
Spoiler :
* Extract it on desktop
* Take a card reader insert memory card into the card reader nd connect it to the pc
* From the extracted folder run Diskdump2.exe
* Select generic storage Device. pictures below follw it
* Now to write the scripts folle the below given picr
Now done yu are succesfully created Dead boot memorycard
To continue further
Requerments:
* Z3X samsung Box or SPT Box (i used z3x)
* special UART Cable (300k or 500k uartcable)
* Download teraterm-4.78 From Download
Spoiler :
* Fully charged battery
Dead boot Reapairing procedure
* Download nd extract teraterm-4.78 on desktop
* From extracted folder run ttermpro.exe there select serial port nd change the serial port to z3x serial
port lik below givin in the picr
*After Select The Serial Port Press Ok Button den Go To Setup Click Serial Port Option
Select Baud Rate 115200 Then Press Ok Button lik below givn in the picr
* Now insert the created boot card to the mobile
* Connect the Uart cable via z3x box
* Now Insert the battery nd wait for 5min if the procces didnt start discnnt the mobile close ttermpro agin try it.
* if it run success yu vil the result below given lik this.
Quote:
| pit_check_integrity: invalid pit.(0x0) pit_check_integrity: invalid pit.(0x0) update_guid_partition_table: There is no pit binary. fsd_reclaim 1283: MST is not recognized(mst.magic=0x0) fsd_reclaim 1284: MST is not recognized fsd_reclaim 1599: Error(nErr=0x0) fsd_reclaim 1604: j4fs_rw_start is set to default value(128KB) j4fs_open 153: Error(nErr=0x40000000) j4fs_read_file_bootloader 355: j4fs panic load_j4fs_param: 'param.j4fs' does not exist, make new one.. j4fs_write_file_bootloader 184: j4fs panic fail j4fs_read_file_bootloader 355: j4fs panic load_j4fs_param: debug level file does not exist..*INCORRECT!* init_fuel_gauge: battery is not detected, do not init fuelgauge init_microusb_ic: MUIC: CONTROL1:0x1b init_microusb_ic: MUIC: CONTROL1:0x1b init_microusb_ic: MUIC: CONTROL2:0x3b init_microusb_ic: MUIC: CONTROL2:0x3a PMIC_ID = 0x2 PMIC_IRQSRC = 0x0 PMIC_STATUS1 = 0x10 PMIC_STATUS2 = 0x0 PMIC_PWRON = 0x2 PMIC_IRQ1 = 0x27 PMIC_IRQ2 = 0x0 s5p_check_keypad: keypad value=0x0 s5p_check_reboot_mode: INFORM3 = 0 ... skip s5p_check_upload: MAGIC CODE=d1b0f038 microusb_get_attached_device: STATUS1:0x3c, 2:0x0 s5p_check_download: update mode=0 j4fs_read_file_bootloader 355: j4fs panic s5p_check_tzsw: invalid tzsw type! dummy? scr_draw_image: draw 'download_error.jpg'... j4fs_read_file_bootloader 355: j4fs panic read_param_file: 'download_error.jpg' j4fs read failed! fimd_div:13, div:1, FB_SOURCE_CLOCK:800000000, FB_PIXEL_CLOCK:57153600 a2, 60, 90, |
* if yu get this error at the end [Patch Stop] This is not Rom Code. yu cant fix yur mobile yu have to change yur emmc chip
Quote:
| TN default [DVFS] INT(1) : 0 DRAM Type : LPDDR2 8G [DVFS] MIF(3) : 0 [EPLL][VPLL][CLK_DIV] OK [LOCK SW/HW]ARM:0/0 INT:0/0 G3D:0/0 MIF:0/0 SHIFT:0/0 [DVFS] ARM(0) : 5 [DVFS] INT(1) : 0 [DVFS] G3D(2) : 0 [DVFS] MIF(3) : 0 [SD_INIT SDMMC_HighSpeedONE] SD_READ: 20000 20000 0x40008000 -> 668484 usec Inp32(uAddr) : 0xea00007e FW Booting [Patch Stop] This is not Rom Code. |
* After done this yur mobile must me n download mode or white screen if white screen manually put into download mode.
* After dead boot repair mine white screen i manually put into download mode pir below
* Now update your mobile with factory firmware with PIT file lik below given n the picr.Factory firmware
Spoiler :
* After update complete yur mobile may not have imei .imei null or yur mobile will not boot bcoz of dead boot repair. yur efs must be corrupted
* To Fix this prob first root yur mobile
Spoiler :
* Now Download this EfS repair file nd flash it through odin select as odin yur mobile must boot
but the imei become lik this 004999010640000
Spoiler :
* if yur imei is null yu cant repair using this box so 1st yu have to repair the efs using above givn file. if yur imei bcome lik tis oly (004999010640000) yu can repair using z3x or othr samsung tool
* Now follw the picr to repair imei problem.
After IMEI Repair
▬▬▬▬▬▬▬▬ஜ ۩۞۩ ஜ▬▬▬▬▬▬▬▬
أهلا وسهلا يك (زائر) في منتديات التونسية للمحمول
قوانين منتدى التونسية للمحمول ( المرور من هنا واجب )
طريقة الإنظمام إلي مجموعة أعضاء سبور € GSM Tn
هام لكل الأعضاء الجدد {اخي ..}، كنت عضومنذُ{8 أيام الأخيرة..}
كتبت وقد أيقنت يوم كتابتي بأن يدي تفنى ويبقى كتابها فإن كتبت خيرا ستجزى بمثله وإن كتبت شراً عليها حسابها...
قوانين منتدى التونسية للمحمول ( المرور من هنا واجب ) طريقة الإنظمام إلي مجموعة أعضاء سبور € GSM Tn هام لكل الأعضاء الجدد {اخي ..}، كنت عضومنذُ{8 أيام الأخيرة..}كتبت وقد أيقنت يوم كتابتي بأن يدي تفنى ويبقى كتابها فإن كتبت خيرا ستجزى بمثله وإن كتبت شراً عليها حسابها...